Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterClopay Torsion Spring Replacement: The Schertz Owner’s Guide
Clopay torsion spring replacement in Schertz typically runs $180-$340 installed, and we stock the common sizes on the truck so most jobs are done same day. If you heard a bang from the garage and the door won’t lift more than a few inches, that’s the spring letting go, not the opener. A torsion spring is the muscle that does the heavy lifting. The opener just guides it. Our crews run Clopay-compatible springs out to neighborhoods all over Schertz, from the older subdivisions off FM 1518 out toward Schertz Parkway, and we quote the full price before we touch anything.
Which Clopay Models This Applies To
We replace torsion springs on every Clopay residential line we see in Schertz: the Classic, Gallery, Coachman, Bridgeport, Reserve, and Value series. The compatibility gotcha most homeowners never hear about is wire size. Two springs can look identical sitting on a bench, but a .207 wire spring isn’t interchangeable with a .225. The wire diameter, inside diameter, and length all have to match the weight of your exact door, not just the general model. Clopay stamps identifying numbers on the spring cone, and we read those before we quote anything. If the cone is rusted past reading, we measure the old spring and cross-reference the door weight instead.
On OEM versus aftermarket: Clopay doesn’t manufacture its own torsion springs. They’re built to spec by companies that also sell quality aftermarket equivalents. We install both, and for most Schertz homes the aftermarket spring is the better buy because it carries the same cycle rating without the brand markup. What matters is the cycle count stamped on the spring, and we’ll tell you what’s on yours before we install it. Otto’s Garage Door is an independent service provider, not affiliated with Clopay, which means we stock the spring that fits your door rather than pushing one brand’s box.
Signs Your Clopay Torsion Spring Replacement Is Failing
- Door feels heavy when you pull the release cord: A healthy spring carries nearly all of the door’s weight. When you can’t lift it with one hand, the spring has lost tension and is near the end.
- Visible gap in the spring coil: A torsion spring snaps clean through, and the two halves separate. You’ll see a half-inch to two-inch gap somewhere along the coil.
- Door rises unevenly or jerks on the way up: If one spring has failed on a two-spring door, the remaining spring is now carrying double its rated load. It won’t do that for long.
- Loud bang from the garage at night: That’s the sound of a spring breaking under full tension. It’s not the door frame settling.
- Opener runs but the door barely moves: The opener motor doesn’t have the strength to replace a broken spring. If it’s straining, the problem is almost never the opener.
Replacement Cost & What’s Included
Clopay torsion spring replacement in Schertz runs $180-$340, and the spread comes down to spring size and how many springs your door carries. A single-spring residential door sits at the lower end. A heavier two-spring setup with thicker wire lands toward the top of that range. Every quote covers the springs, cable checks, bearing inspection, balance testing, and cleanup. We quote a number over the phone and that number doesn’t change when the truck pulls up.
- Single torsion spring replacement: $180-$260 installed
- Dual torsion spring replacement: $240-$340 installed
- Spring plus center bearing replacement: add $35-$60
- Spring plus cable replacement: add $130-$250 per cable set
The price is quoted and agreed before any work starts. Every job gets the 90-Day Done Right Promise in writing: if it isn’t right, one call brings us back. No invoice surprises, no parts that suddenly need replacing once we’re in the driveway.
DIY or Call Us?
A door is 200 pounds riding on two springs. Respect it. The torsion spring sits under enough stored energy to take off a finger or worse if the winding bars slip. We don’t hand out step-by-step instructions for winding torsion springs, and any video that does is selling you a trip to the ER. What you can safely do before calling: check whether one spring or both look separated, clear anything wedged under the door, and see if the door will lift evenly with the release cord pulled. That tells us a lot. Then call (830) 341-1180 and describe what you’re seeing. We’ll quote it over the phone and hold that number.
FAQs
A standard Clopay torsion spring is rated for 10,000 cycles, which in a Schertz home usually works out to seven to ten years. Open and close the door three times a day, and you’re at 10,000 cycles in roughly nine years. Our summers accelerate rust on exposed steel, and we count spring cycles the way you count tire miles. If your door is nearing that age and the spring looks rusted at the coil, plan for replacement before it breaks. Call (830) 341-1180 and we’ll inspect it during a regular service call.
Can a broken torsion spring be repaired instead of replaced?
No. A snapped torsion spring is done. You can’t weld a spring that holds thousands of pounds of stored tension and expect it to hold. We replace both springs on a two-spring door at the same time because the surviving spring has the same cycle count as the one that broke. Replacing only one means you’re back in the driveway with the same problem in a year. We’ll quote both springs upfront so there’s no surprise on the invoice.
How long does a Clopay torsion spring replacement take?
Most single or dual torsion spring replacements in Schertz take 45 to 90 minutes from when we start unbolting the old cones to when the door is balanced and tested. If we’re also replacing cables or the center bearing, add another half hour. We carry the common Clopay-compatible spring sizes, cones, and cables on the truck, so we typically complete the job in one visit.
Do you stock Clopay torsion springs on the truck?
Yes. We run our trucks stocked with torsion springs in the wire sizes and inside diameters that cover the vast majority of Clopay residential doors in Schertz. That includes the heavier wire sizes for two-car doors and the lighter springs on single doors. If your door needs an unusual size we don’t have on the shelf, we’ll have it in hand within one business day and back on your door the next morning. Call (830) 341-1180 and tell us the model stamped on your Clopay label, and we’ll confirm we have your spring before we roll out.
If your Clopay spring broke this morning, call (830) 341-1180. We answer live, quote over the phone, and hold that price when we get there. Free estimate, no trip charge inside the county, and the 90-Day Done Right Promise in writing on every job.
Written by Otto Reinhardt, Owner, Otto’s Garage Door - Schertz, TX at Otto’s Garage Door, serving Schertz and nearby areas.